I/O enclosure (2U) part numbers (Model 983)

Information about 2U I/O enclosure parts is listed below. Use Table 1 as a directory.

Note: The following part numbers are the most recent for this version of the Parts Catalog. Your storage facility or serviceable event FRU list might contain an older or newer part number. The parts-ordering system recognizes all valid part numbers and automatically substitutes an available part number as needed.
Table 1. Start here, I/O enclosure (2U) part numbers (Model 983)
Part name Figure
I/O enclosure (2U) fan Figure 1
I/O enclosure (2U) front bezel Figure 1
I/O enclosure (2U) power supply Figure 1
I/O enclosure (2U) adapter (Fibre Channel host) Figure 5
I/O enclosure (2U) adapter (PCIe) Figure 4
I/O enclosure (2U) adapter (PCIe and SAS device) Figure 3
I/O enclosure (2U) adapter (PCN) Figure 6
I/O enclosure (2U) midplane assembly Figure 2
All other parts (Find the appropriate figure below)
Figure 1. I/O enclosure (2U) locations (front) (model 983)
I/O enclosure (2U) locations (front) (model 983)
Table 2. I/O enclosure (2U) FRUs, front (Model 983)
Index Part name CCIN1 Part number
A1, A2 Fan   02AN058
Not shown Front bezel   02AN734
E1, E2 Power supply   01KL609
Notes:
  1. Important, read this entire paragraph as there are exceptions to what part number to order. The custom card identification number (CCIN) identifies the physical features and logical behavior of a part. If two parts appear physically identical but have different CCINs, they are not interchangeable unless stated elsewhere in the maintenance package or by the next level of support. If two parts have different part numbers and yet have the same CCIN, they are interchangeable. When you order a part number that is reported in a serviceable event or call-home record, check whether the parts ordering system has a conditional substitute for DS8000® series. There are a couple of exceptions where the part number on the DS8000 FRU part number is not the same one that is reported and called home. The part number reported and called home may be the original eServer part number which may have firmware that is not appropriate for the DS8000 series. You must order the DS8000 FRU part number to ensure that the correct firmware is present.
Figure 2. Location codes, I/O enclosure (2U) (rear) (model 983)
I/O enclosure (2U) locations code (rear) (model 983) with logical IG3, 1G4
Figure 3. Location codes, I/O enclosure (2U) adapter (PCIe and SAS device)
I/O enclosure (2U) adapter (generic)
Figure 4. Location codes, I/O enclosure (2U) adapter (PCIe)
Location codes, I/O enclosure (2U) adapter (PCIe
Figure 5. Location codes, I/O enclosure (2U) adapter (Fibre Channel host)
I/O enclosure (2U) adapter (Fibre Channel host)
Figure 6. Location codes, I/O enclosure (2U) adapter (PCN)
Location codes, I/O enclosure (2U) adapter (PCN)
Table 3. I/O enclosure (2U) FRUs, rear (Model 983)
Location I/O enclosure part name CCIN1 Part number
P1 I/O enclosure (2U) midplane assembly
Figure 2		   02AN688
P1-C1
P1-C8		 I/O enclosure (2U) adapter (PCIe and SAS device)
Figure 3		 2E0E 02AN008
P1-C2
P1-C7		 I/O enclosure (2U) adapter (PCIe)
Figure 4		 2E0D 02AN007
P1-C3
P1-C4
P1-C5
P1-C6		 I/O enclosure (2U) adapter (Fibre Channel host), SW 16 Gb (4-port)
Figure 5		 HD4S 02AM489
P1-C3
P1-C4
P1-C5
P1-C6		 I/O enclosure (2U) adapter (Fibre Channel host), LW-10 km 16 Gb (4-port)
Figure 5		 HD4L 02AM405
P1-C9 I/O enclosure (2U) adapter (PCN)
Figure 6		 2E0F 02AN571
Notes:
  1. Important, read this entire paragraph as there are exceptions to what part number to order. The custom card identification number (CCIN) identifies the physical features and logical behavior of a part. If two parts appear physically identical but have different CCINs, they are not interchangeable unless stated elsewhere in the maintenance package or by the next level of support. If two parts have different part numbers and yet have the same CCIN, they are interchangeable. When you order a part number that is reported in a serviceable event or call-home record, check whether the parts ordering system has a conditional substitute for DS8000 series. There are a couple of exceptions where the part number on the DS8000 FRU part number is not the same one that is reported and called home. The part number reported and called home may be the original eServer part number which may have firmware that is not appropriate for the DS8000 series. You must order the DS8000 FRU part number to ensure that the correct firmware is present.
Table 4. I/O enclosure (2U) cable FRUs, rear (Model 983)
Location I/O enclosure part name Part number
P1-C1-T1, T2, T3, T4 Cable, serial attached SCSI (SAS); see: Storage enclosure part numbers, Models 98x, 8xE (SAS flash enclosure, 24 drive slots).
P1-C1-T5, T6 CEC enclosure PCIe cable; see CEC enclosure part numbers, Models 980, 983, 984.
P1-C1-T7 Not used
P1-C3-Tx
P1-C4-Tx
P1-C5-Tx
P1-C6-Tx
x = 1, 2, 3, 4		 Host cable, provided by customer
P1-C2-T5, T6 CEC enclosure PCIe cable; see CEC enclosure part numbers, Models 980, 983, 984.
P1-C2-T7 Not used
P1-C7-T5, T6 CEC enclosure PCIe cable; see CEC enclosure part numbers, Models 980, 983, 984.
P1-C7-T7 Not used
P1-C8-T1, T2, T3, T4 Cable, serial attached SCSI (SAS); see: Storage enclosure part numbers, Models 98x, 8xE (SAS flash enclosure, 24 drive slots).
P1-C8-T5, T6 CEC enclosure PCIe cable; see CEC enclosure part numbers, Models 980, 983, 984.
P1-C8-T7 Not used
P1-C9-T1 Power control network (PCN) cable 02AN466
P1-C9-T2 Power control network (PCN) cable 02AN467